Paver Patio Cost Calculator & Price Guide

A paver patio is built from individual interlocking units, usually brick, concrete, or natural stone, set on a compacted base. The finished price depends on the size of the patio, the paver material, the site, and how much of the work you hire out. Material and labor are the two biggest pieces, and size is what scales both.

Prices below come from This Old House and Lawn Love, with check dates of Oct 13, 2026 and Oct 13, 2026. The sources define a typical patio differently, so the tables break the cost into parts you can compare.

Cost per square foot is the quickest way to estimate a project, because you can multiply it by your patio area.

This Old House reports $8 – $25/sq ft. Lawn Love reports $8 – $24/sq ft. The two ranges are nearly the same. The low end may reflect simpler materials on an easy site, and the high end may reflect premium materials or difficult conditions. The sources do not say exactly what each end includes, so treat the range as a planning figure.

Measure the length and width of the patio in feet and multiply them to get square footage. Then multiply that area by the low and high ends of the per-square-foot range. The result is a budget window you can check against quotes.

Small patios do not always scale evenly. Fixed costs such as delivery, equipment, and site setup spread across fewer square feet, so a small patio can cost more per square foot than a large one. The size table shows several common patio footprints.

A 60-square-foot patio is listed at $480 – $1,440, and an 8-by-12-foot patio (96 square feet) is listed at $768 – $2,400. A 100-square-foot patio is listed at $800 – $2,400. Larger patios climb quickly: a 200-square-foot patio is listed at $1,600 – $4,800, and a 300-square-foot patio is listed at $2,400 – $7,200.

The paver itself is only one part of the total. These figures are for the pavers alone, not the base material, sand, or labor.

Interlocking pavers are the least expensive at $3 – $6/sq ft. Brick pavers are listed at $4 – $8/sq ft. Flagstone is the most expensive at $13 – $30/sq ft. Natural stone costs more and often takes more skill to lay, so the price gap can widen once labor is included.

Contractors bill labor either by the hour or by the square foot. Both methods appear in published guides.

Labor for laying pavers is listed at $50 – $80/hr.

On a per-square-foot basis, This Old House lists $4 – $11/sq ft and Lawn Love lists $5 – $15/sq ft. Labor includes excavation, base preparation, laying and cutting the pavers, and filling the joints. A patio on uneven ground or one that needs a retaining edge takes more labor.

A published total depends on the assumptions behind it.

This Old House gives a range of $2,400 – $7,000. Lawn Love gives $2,275 – $6,950 for a 280-square-foot patio. The sources differ on patio size, material mix, and region. Compare any quote with these figures by looking at the patio area and the paver type first.

• Patio size. Larger patios cost more in total, though often less per square foot.
• Paver material. Concrete, brick, and natural stone sit at different price points.
• Pattern and shape. Curves, borders, and complex patterns take more cutting and time.
• Site conditions. Slopes, poor drainage, tree roots, or soft soil add excavation and base work.
• Base depth and drainage. A well-prepared base keeps pavers from settling, so skimping here costs more later.
• Access. Delivery of heavy pallets to a backyard with a narrow gate takes extra labor.
• Local labor rates. Prices vary by region.
• Extras. Seating walls, lighting, and fire pits are separate line items.

Pavers offer more design flexibility than a poured slab, and individual units can be lifted and reset if the ground shifts. A damaged paver can be swapped out without redoing the whole surface. Poured concrete, by contrast, cracks as a single piece. Pavers also need periodic maintenance, such as refilling joint sand and treating weeds, and the surface can settle if the base is poorly built.

Laying pavers is a physically demanding job. The work includes excavating, compacting the base, setting a level surface, and cutting pavers to fit. Mistakes in base preparation show up later as sunken or uneven spots. If you consider doing part of the work yourself, such as removing sod or hauling material, ask a contractor whether they will quote labor separately. Check your local rules on permits, setbacks, and utility locations before any digging begins, and have underground utilities marked.

• What is the total square footage, and what price per square foot does the quote use?
• Which paver brand and style are included?
• How deep is the base, and what material is it?
• Does the quote include excavation, haul-away, edge restraints, and joint sand?
• Who handles permits or homeowners association approvals?
• What warranty covers settling or paver failure?